The new EHEIM aquaAlert+e is a high-precision, intelligent conductivity meter for continuously monitoring the water quality within your aquarium. By accurately recording the electrical conductance (μS/ cm), the device provides precise data on the salt content and potential contaminants TDS (total dissolved solids) such as sodium chloride, nitrite and nitrate ( build-up of organic waste). The device recognises such changes at an early stage, it will reliably warn you if limit values are exceeded and will provide specific recommendations for necessary measures such as water changes or water hardening to ensure a stable water quality. Thanks to smart algorithms, EHEIM aquaAlert+e also calculates the estimated time until your next water change and therefore supports optimum maintenance of your aquarium.The integrated temperature measurement also aids with safety: if the water temperature rises above a predefined value, the appliance will sound an alarm. The dry-running warning and electrode cleaning reminders also help you to keep the water quality at the highest level in the long term or can warn you if there is a need to top up the aquarium or save your fish in the case of a potential failure of your aquarium. Note: The basis for the information on the water change is the conductivity measured in the water of your aquarium. We therefore recommend calling up the current water change information at lunchtime, for example when CO2 fertilisation is in operation or after the water change and the addition of all components such as water conditioner and plant fertiliser.Features of the EHEIM aquaAlert+eWarning system with integrated WLAN function (Wifi) and wireless control via smartphone, tablet or PC/MacPrecise measurements of the aquarium through calibration Individual warning with customisable limit values  Alarm in the event of a sudden increase in conductivity >50 % within one hour) Multiple warning levels with corresponding recommendations for action  Colour-coded visual display of the warning level (green/ yellow/ red)  Automatic calculation of the time until the next water change based on gathered data history • Notification if the temperature is exceeded or the electrode runs dry  Reminder for electrode cleaning for permanently precise measured values; automatic

EHEIM classicLEDcontrol+e allows you to control the brightness level in your aquarium easily without cables. Sunrise, sunset, cloud effects, moonlight ... The natural changes in brightness in your aquarium contributes a lot to the well-being of plants and animals. With our classicLEDcontrol+e lighting control system, you can simulate the natural course of light in the day - and even set a natural moon cycle. The controller offers you maximum performance, high power, a stable connection, and compatibility with all devices of the EHEIM Digital family.The classicLEDcontrol+e is quick to install, and you simply programme and control it via smartphone, tablet, or PC. You can even select one of the pre-installed lighting scenarios. Or you can create your own scenario and adjust the brightness level individually. The lighting control only works in conjunction with EHEIM classicLED luminaires. When changing the light source (e.g. T5/T8 to classicLED) or when setting up your aquarium from scratch, you can use the acclimatisation function to help you. In addition, the controller automatically checks whether a new software update is available if a network connection is existing. All updates can also be downloaded free of charge from the EHEIM website. Advantages of the EHEIM classicLEDcontrol+e Optimised controller with maximum performance, high power, and a stable connection. Compatible with all devices of the EHEIM Digital family. Control the aquarium lighting - only available with EHEIM classicLED luminaires and EHEIM classicLED power supplies. Wireless operation via WLAN-capable end devices (smartphone, tablet, PC/Mac). Two connections can be controlled separately; allowing two individual lighting scenarios to be used together, i.e., several luminaires can be controlled individually or in synchronicity. Simulate the lighting over of the course of the day as in nature. Use pre-installed lighting scenarios for different living spaces. Use/create individually programmable lighting sequences. Create moonlight scenarios with natural moon phases. Freely configurable scenarios: sunrise, sunset (each lasting up to 3 hours), cloud effects, moonlight, etc. Lighting scenarios can be saved, loaded and shared online. Comes with an expert mode with additional setting options. Comes with an acclimatisation mode, e.g. when changing light source (T5/T8 to classicLED) or when setting up new aquariums. Built in-optimum settings for the luminaires: "classicLED daylight" and "classicLED plants“ Has a quick run feature to test selected settings. Automatic changeover of summer and winter time. Software updates free of charge for download on the EHEIM website. Automatic update with existing internet connection. Energy consumption display. Highest safety and reliability - 3 years warranty.  

EHEIM classicVARIO+e - the smart version of the classic filter, proven millions of times, with wireless electronic control and the world‘s unique BLDC pump in an external filter. With the EHEIM classicVARIO+e you choose three things: First, for the „+e version“ of our reliable, proven millions of times classic filter. Second, for the innovation through wireless electronic control via smartphone, tablet or PC/Mac. And third, for an external filter with a particularly quiet BLDC pump. This means the highest quality, first-class components and carefully coordinated functions.You can adjust the pump performance continuously (different modes). When linked with the devices of the EHEIM Digital Family, the function is coordinated accordingly. For example, the pump performance reduces during feeding with the autofeeder+. Or when coupled with the LEDcontrol+e, the performance adapts to the set day/night rhythm. And when the next cleaning is due, the classicVARIO+e calculates it, informs you through a maintenance indicator and reminds you by e-mail if necessary.Benefits of the EHEIM classicVARIO+e Digital advancement of the reliable, proven millions of times classic external filter generation Electronic filter with integrated WLAN function (Wifi ) and wireless control via smartphone, tablet or PC/Mac Pump performance continuously adjustable Different pump functions - Manual and Pulse Mode Very low power consumption possible through power regulation (1.7- 9,8 W) Connectable with products of the EHEIM Digital Family: E.g. adjustment of the pump performance during feeding when coupled with the EHEIM autofeeder+ as well as harmonization with the set day/night rhythm when linked with the LEDcontrol+e Maintenance indicator indicates calculated due cleaning; automatic reminder by e-mail Permanently elastic silicone seal on the pump head (for easy and safe closing after cleaning) Can be equipped with filter mats and/or loose filter media Highly effective BLDC pump (brushless direct current motor) ensures quiet, low-vibration operation and large control range with fine gradation Includes spray bar, intake pipe, hose and installation accessories Suitable for fresh and salt water 2 years warranty

You can use EHEIM climacontrol+ to cool down the water temperature on hot days or warm it up on cold days, just as your aquarium inhabitants need it.EHEIM climacontrol+ is our new electronically controlled climate control device. You simply set the ideal water temperature wirelessly - via smartphone, tablet, or PC/MAC. If the water is too warm, the unit automatically cools down, and if it gets too cold it warms up. The unit monitors and controls everything.Also, it gives you advanced warning of any problems, such as if the required temperature is exceeded or undershot by 2 °C for more than 5 minutes, you receive a warning e-mail.High outdoor temperatures often cause the aquarium water to overheat in summer. This is extremely harmful to fish and all other living creatures. For example if the temperature is too high, corals die in the marine aquarium, and in freshwater aquariums, oxygen deficiency and algae proliferation occur quickly.EHEIM climacontrol+ is the optimal climate control device for aquariums. It has low energy consumption and works with environmentally friendly coolant.There are three climate control devices available: S, M and L - for aquariums up to 500, 1000 and 2000 litres and come with a 3-year warranty.Features of the EHEIM climacontrol+ Electronically controlled continuous flow climate control device with Wi-Fi functionality Temperature setting and control over WiFi via smartphone, tablet, or PC/MAC Cooling and heating mode Constant regulation of water temperature Temperature control of water in freshwater and marine aquariums Precise temperature detection from 5 °C up to 35 °C Switches on automatically above or below a set target temperature Warning e-mail if temperature exceeds or falls below 2 °C for more than 5 minutes Constantly displays the current water temperature when in operation Use in the ambient temperature range from 10 °C to 38 °C Very energy-efficient and environmentally friendly climate control devicewith ozone-friendly refrigerant (R290) To be operated exclusively with clean (filtered) water; i.e. for marine aquariums via separate pump with water from the filter tank or for freshwater aquariums position behind the external filter (alternatively via separate pump with pre-filter directly from the aquarium) There are three climate control devices: S, M and L - for aquariums up to 500, 1000 and 2000 litres Made of High quality parts and materials, and comes with 3 years warranty Important for marine water aquariums: Optimum temperature for corals between 24 and 26 °C; above 29.5 °C they die. Important for fresh water aquariums: The temperature should always be below 30 °C. Above this temperature there is a risk of oxygen deficiency, inhibited plant growth, algae proliferation.EHEIM climacontrol+ – the electronically controlled climate control devicewith WLAN function and many advantagesEHEIM climacontrol+ has the main task of cooling down the aquarium water when the temperature is too high. It provides both a cooling and a heating function.In summer, high outside temperatures often lead to overheating of the aquarium water - e.g. in a small room that heats up quickly, in an attic flat, in sunlight, etc. Even in basins that are closed at the top so that the warmth from the lighting cannot escape, there is occasionally a build-up of heat. EHEIM climacontrol+ offers WLAN function. The WiFi controller is used to set the optimum target temperature via smartphone, tablet or PC/MAC. As soon as the temperature exceeds or falls below the target value, the unit switches on and cools or heats the water until the target value is reached. The current water temperature is always displayed. If the set temperature is exceeded or undershot by 2 °C for more than 5 minutes, you will receive a warning e-mail.EHEIM climacontrol+ is a continuous flow unit and should only be operated with clean (filtered) water. For marine water aquariums, this means with water from the filter tank (with a separate pump). In freshwater aquariums by placing it behind the external filter. (Alternatively, operation via a separate pump - but with a pre-filter - directly from the aquarium is also possible here).EHEIM climacontrol+ works energy-efficiently and environmentally friendly. The refrigerant (R290) replaces ozone-depleting coolants and the global warming potential (GWP) is in the minimum range.When positioning the unit, make sure that the ventilation openings are always kept clear. The distance to walls etc. should be at least 50 mm. In the base cabinet of an aquarium combination, for example, appropriate recesses must be provided for fresh air supply and warm exhaust air (for more details, see the operating instructions).ATTENTION! The climate control device may only be stored, transported and operated in an upright position!

You can use EHEIM climacontrol+ to cool down the water temperature on hot days or warm it up on cold days, just as your aquarium inhabitants need it.EHEIM climacontrol+ is our new electronically controlled climate control device. You simply set the ideal water temperature wirelessly - via smartphone, tablet, or PC/MAC. If the water is too warm, the unit automatically cools down, and if it gets too cold it warms up. The unit monitors and controls everything.Also, it gives you advanced warning of any problems, such as if the required temperature is exceeded or undershot by 2 °C for more than 5 minutes, you receive a warning e-mail.High outdoor temperatures often cause the aquarium water to overheat in summer. This is extremely harmful to fish and all other living creatures. For example if the temperature is too high, corals die in the marine aquarium, and in freshwater aquariums, oxygen deficiency and algae proliferation occur quickly.EHEIM climacontrol+ is the optimal climate control device for aquariums. It has low energy consumption and works with environmentally friendly coolant.There are three climate control devices available: S, M and L - for aquariums up to 500, 1000 and 2000 litres and come with a 3-year warranty.Features of the EHEIM climacontrol+ Electronically controlled continuous flow climate control device with Wi-Fi functionality Temperature setting and control over WiFi via smartphone, tablet, or PC/MAC Cooling and heating mode Constant regulation of water temperature Temperature control of water in freshwater and marine aquariums Precise temperature detection from 5 °C up to 35 °C Switches on automatically above or below a set target temperature Warning e-mail if temperature exceeds or falls below 2 °C for more than 5 minutes Constantly displays the current water temperature when in operation Use in the ambient temperature range from 10 °C to 38 °C Very energy-efficient and environmentally friendly climate control devicewith ozone-friendly refrigerant (R290) To be operated exclusively with clean (filtered) water; i.e. for marine aquariums via separate pump with water from the filter tank or for freshwater aquariums position behind the external filter (alternatively via separate pump with pre-filter directly from the aquarium) There are three climate control devices: S, M and L - for aquariums up to 500, 1000 and 2000 litres Made of High quality parts and materials, and comes with 3 years warranty Important for marine water aquariums: Optimum temperature for corals between 24 and 26 °C; above 29.5 °C they die. Important for fresh water aquariums: The temperature should always be below 30 °C. Above this temperature there is a risk of oxygen deficiency, inhibited plant growth, algae proliferation.EHEIM climacontrol+ – the electronically controlled climate control devicewith WLAN function and many advantagesEHEIM climacontrol+ has the main task of cooling down the aquarium water when the temperature is too high. It provides both a cooling and a heating function.In summer, high outside temperatures often lead to overheating of the aquarium water - e.g. in a small room that heats up quickly, in an attic flat, in sunlight, etc. Even in basins that are closed at the top so that the warmth from the lighting cannot escape, there is occasionally a build-up of heat. EHEIM climacontrol+ offers WLAN function. The WiFi controller is used to set the optimum target temperature via smartphone, tablet or PC/MAC. As soon as the temperature exceeds or falls below the target value, the unit switches on and cools or heats the water until the target value is reached. The current water temperature is always displayed. If the set temperature is exceeded or undershot by 2 °C for more than 5 minutes, you will receive a warning e-mail.EHEIM climacontrol+ is a continuous flow unit and should only be operated with clean (filtered) water. For marine water aquariums, this means with water from the filter tank (with a separate pump). In freshwater aquariums by placing it behind the external filter. (Alternatively, operation via a separate pump - but with a pre-filter - directly from the aquarium is also possible here).EHEIM climacontrol+ works energy-efficiently and environmentally friendly. The refrigerant (R290) replaces ozone-depleting coolants and the global warming potential (GWP) is in the minimum range.When positioning the unit, make sure that the ventilation openings are always kept clear. The distance to walls etc. should be at least 50 mm. In the base cabinet of an aquarium combination, for example, appropriate recesses must be provided for fresh air supply and warm exhaust air (for more details, see the operating instructions).ATTENTION! The climate control device may only be stored, transported and operated in an upright position!

You can use EHEIM climacontrol+ to cool down the water temperature on hot days or warm it up on cold days, just as your aquarium inhabitants need it.EHEIM climacontrol+ is our new electronically controlled climate control device. You simply set the ideal water temperature wirelessly - via smartphone, tablet, or PC/MAC. If the water is too warm, the unit automatically cools down, and if it gets too cold it warms up. The unit monitors and controls everything.Also, it gives you advanced warning of any problems, such as if the required temperature is exceeded or undershot by 2 °C for more than 5 minutes, you receive a warning e-mail.High outdoor temperatures often cause the aquarium water to overheat in summer. This is extremely harmful to fish and all other living creatures. For example if the temperature is too high, corals die in the marine aquarium, and in freshwater aquariums, oxygen deficiency and algae proliferation occur quickly.EHEIM climacontrol+ is the optimal climate control device for aquariums. It has low energy consumption and works with environmentally friendly coolant.There are three climate control devices available: S, M and L - for aquariums up to 500, 1000 and 2000 litres and come with a 3-year warranty.Features of the EHEIM climacontrol+ Electronically controlled continuous flow climate control device with Wi-Fi functionality Temperature setting and control over WiFi via smartphone, tablet, or PC/MAC Cooling and heating mode Constant regulation of water temperature Temperature control of water in freshwater and marine aquariums Precise temperature detection from 5 °C up to 35 °C Switches on automatically above or below a set target temperature Warning e-mail if temperature exceeds or falls below 2 °C for more than 5 minutes Constantly displays the current water temperature when in operation Use in the ambient temperature range from 10 °C to 38 °C Very energy-efficient and environmentally friendly climate control devicewith ozone-friendly refrigerant (R290) To be operated exclusively with clean (filtered) water; i.e. for marine aquariums via separate pump with water from the filter tank or for freshwater aquariums position behind the external filter (alternatively via separate pump with pre-filter directly from the aquarium) There are three climate control devices: S, M and L - for aquariums up to 500, 1000 and 2000 litres Made of High quality parts and materials, and comes with 3 years warranty Important for marine water aquariums: Optimum temperature for corals between 24 and 26 °C; above 29.5 °C they die. Important for fresh water aquariums: The temperature should always be below 30 °C. Above this temperature there is a risk of oxygen deficiency, inhibited plant growth, algae proliferation.EHEIM climacontrol+ – the electronically controlled climate control devicewith WLAN function and many advantagesEHEIM climacontrol+ has the main task of cooling down the aquarium water when the temperature is too high. It provides both a cooling and a heating function.In summer, high outside temperatures often lead to overheating of the aquarium water - e.g. in a small room that heats up quickly, in an attic flat, in sunlight, etc. Even in basins that are closed at the top so that the warmth from the lighting cannot escape, there is occasionally a build-up of heat. EHEIM climacontrol+ offers WLAN function. The WiFi controller is used to set the optimum target temperature via smartphone, tablet or PC/MAC. As soon as the temperature exceeds or falls below the target value, the unit switches on and cools or heats the water until the target value is reached. The current water temperature is always displayed. If the set temperature is exceeded or undershot by 2 °C for more than 5 minutes, you will receive a warning e-mail.EHEIM climacontrol+ is a continuous flow unit and should only be operated with clean (filtered) water. For marine water aquariums, this means with water from the filter tank (with a separate pump). In freshwater aquariums by placing it behind the external filter. (Alternatively, operation via a separate pump - but with a pre-filter - directly from the aquarium is also possible here).EHEIM climacontrol+ works energy-efficiently and environmentally friendly. The refrigerant (R290) replaces ozone-depleting coolants and the global warming potential (GWP) is in the minimum range.When positioning the unit, make sure that the ventilation openings are always kept clear. The distance to walls etc. should be at least 50 mm. In the base cabinet of an aquarium combination, for example, appropriate recesses must be provided for fresh air supply and warm exhaust air (for more details, see the operating instructions).ATTENTION! The climate control device may only be stored, transported and operated in an upright position!

With EHEIM LEDcontrol+e you can easily control the brightness curve and the lighting mood in your aquarium - without cables. A lot depends on the light in your aquarium. Animals and plants react positively to the natural process of brightness and light colours. Our wireless LED controller offers you a variety of settings. Thanks to integrated plug connections, it is quickly installed. Programming is easy on a smartphone, tablet or PC. You do not need an app for this, you control the network of the controller directly. Now select the luminaire and one of the pre-installed lighting scenarios - done. Alternatively, you can enter your individual lighting scenario and set the duration of sunrise and sunset, select moonlight and clouds, etc. The current time is automatically synchronized. And when setting up a new aquarium, you can even use an acclimatisation function. Updates can be downloaded free of charge from the EHEIM website.Advantages of the wireless LED controller EHEIM LEDcontrol+e Control of the aquarium lighting - only in combination with EHEIM powerLED+ lights (from serial no. xxxx05) Integrated plug-in connections Wireless operation via smartphone, tablet or PC/Mac via your own network Simulation of the light variations and light moods as in nature Pre-installed lighting scenarios for fresh and marine water including quick-start guide Individually programmable lighting sequence and control of the colour channels Freely configurable: sunrise, sunset (up to 3 hours each), cloud effects, moonlight etc  Lighting scenarios can also be shared with other aquarists Expert mode with additional setting options Acclimatisation mode when changing light source (T5/T8 to LED) or when setting up a new aquarium Ideal for the "fresh plants" and "marine hybrid" luminaires;here you can individually adjust the brightness curve as well as the light colours  With the "fresh daylight" or "marine actinic" luminaires, you can only define the brightness curve Fast forward to check the selected settings Easy change from summer to winter time at the touch of a button  Updates free of charge for download on the EHEIM website  Highest safety and reliability - 3 years warranty

Only the pHcontrol+e and power supply unit are included in the scope of delivery!EHEIM pHcontrol+e – the smart controller for monitoring and readjusting the pH value in your aquariumWith the EHEIM pHcontrol+e you can easily monitor and optimize the pH in your aquarium via a smartphone, tablet, or PC/MAC simply via a WiFi connection and your web browser. A pH sensor measures the current pH value of the water, and the pHcontrol+e automatically provides the necessary CO2 supply. By controlling the magnetic valve connected in series to the CO2 system it adds as much CO2 as required until the desired pH value is reached.To achieve this you must connect your CO2 system, i.e., a CO2 bottle via pressure reducer as well as magnetic valve (see the EHEIM CO2 sets) and a CO2 diffuser. The pHcontrol+e has a day/night control and can be linked to the lighting control EHEIM LEDcontrol+e (see the EHEIM DIGITAL family). In addition to light, nitrogen, phosphate, trace elements, etc., the plants in your aquarium need CO2 above all as an important nutrient. The better they thrive, the more oxygen they release, which the fish need to breathe. Thus, the EHEIM pHcontrol+e indirectly provides oxygen and the optimal pH value for your fish by adding CO2. This is usually between pH 6 and pH 8; pH 7 is considered a neutral value for reference.Note:The basis for measuring and stabilising the pH value is the carbonate hardness ("KH") of the water. Therefore, the EHEIM pHcontrol+e (in Smart mode) initially queries the KH value. Because KH, CO2 and pH value influence each other.Features of the EHEIM pHcontrol+e A smart controller for monitoring and controlling the pH value in the aquarium by regulating the addition of CO2. Includes Wireless WiFi connection with a WLAN-enabled end device (smartphone, tablet, PC/MAC). Has connection and compatibility with devices of the EHEIM DIGITAL family. Measures the pH value through the pH sensor (measuring range: pH 0 to pH 14). Control range of the controller pH 6 to pH 9. Needs to be coupled via pressure reducer with CO2 bottle (EHEIM CO2 set). Electronically controls addition of CO2 through interposed magnetic valve. Adjusts CO2 addition by linking with LEDcontrol+e (day/night control) in smart mode or simple and extended bio mode with own day/night control. Queries the KH value (carbonate hardness) in advance. Sets water test and calibration reminders. Guided calibrations of the pH sensor. Sends warning for deviation of pH value (up/down). Notes if EHEIM pH sensor needs to be replaced. Provides best performance, high power, stable connection, and large memory capacity through new improved chip generation Highest safety and reliability - 3 years warranty

EHEIM pHcontrol+e – the smart controller for monitoring and readjusting the pH value in your aquariumWith the EHEIM pHcontrol+e you can easily monitor and optimize the pH in your aquarium via a smartphone, tablet, or PC/MAC simply via a WiFi connection and your web browser. A pH sensor measures the current pH value of the water, and the pHcontrol+e automatically provides the necessary CO2 supply. By controlling the magnetic valve connected in series to the CO2 system it adds as much CO2 as required until the desired pH value is reached.To achieve this you must connect your CO2 system, i.e., a CO2 bottle via pressure reducer as well as magnetic valve (see the EHEIM CO2 sets) and a CO2 diffuser. The pHcontrol+e has a day/night control and can be linked to the lighting control EHEIM LEDcontrol+e (see the EHEIM DIGITAL family). In addition to light, nitrogen, phosphate, trace elements, etc., the plants in your aquarium need CO2 above all as an important nutrient. The better they thrive, the more oxygen they release, which the fish need to breathe. Thus, the EHEIM pHcontrol+e indirectly provides oxygen and the optimal pH value for your fish by adding CO2. This is usually between pH 6 and pH 8; pH 7 is considered a neutral value for reference.Note:The basis for measuring and stabilising the pH value is the carbonate hardness ("KH") of the water. Therefore, the EHEIM pHcontrol+e (in Smart mode) initially queries the KH value. Because KH, CO2 and pH value influence each other.Features of the EHEIM pHcontrol+e A smart controller for monitoring and controlling the pH value in the aquarium by regulating the addition of CO2. Includes Wireless WiFi connection with a WLAN-enabled end device (smartphone, tablet, PC/MAC). Has connection and compatibility with devices of the EHEIM DIGITAL family. Measures the pH value through the pH sensor (measuring range: pH 0 to pH 14). Control range of the controller pH 6 to pH 9. Needs to be coupled via pressure reducer with CO2 bottle (EHEIM CO2 set). Electronically controls addition of CO2 through interposed magnetic valve. Adjusts CO2 addition by linking with LEDcontrol+e (day/night control) in smart mode or simple and extended bio mode with own day/night control. Queries the KH value (carbonate hardness) in advance. Sets water test and calibration reminders. Guided calibrations of the pH sensor. Sends warning for deviation of pH value (up/down). Notes if EHEIM pH sensor needs to be replaced. Provides best performance, high power, stable connection, and large memory capacity through new improved chip generation Highest safety and reliability - 3 years warranty

Only the pHsensor and the calibration liquid are included in the scope of delivery! EHEIM pHcontrol+e – the smart controller for monitoring and readjusting the pH value in your aquariumWith the EHEIM pHcontrol+e you can easily monitor and optimize the pH in your aquarium via a smartphone, tablet, or PC/MAC simply via a WiFi connection and your web browser. A pH sensor measures the current pH value of the water, and the pHcontrol+e automatically provides the necessary CO2 supply. By controlling the magnetic valve connected in series to the CO2 system it adds as much CO2 as required until the desired pH value is reached.To achieve this you must connect your CO2 system, i.e., a CO2 bottle via pressure reducer as well as magnetic valve (see the EHEIM CO2 sets) and a CO2 diffuser. The pHcontrol+e has a day/night control and can be linked to the lighting control EHEIM LEDcontrol+e (see the EHEIM DIGITAL family). In addition to light, nitrogen, phosphate, trace elements, etc., the plants in your aquarium need CO2 above all as an important nutrient. The better they thrive, the more oxygen they release, which the fish need to breathe. Thus, the EHEIM pHcontrol+e indirectly provides oxygen and the optimal pH value for your fish by adding CO2. This is usually between pH 6 and pH 8; pH 7 is considered a neutral value for reference.Note:The basis for measuring and stabilising the pH value is the carbonate hardness ("KH") of the water. Therefore, the EHEIM pHcontrol+e (in Smart mode) initially queries the KH value. Because KH, CO2 and pH value influence each other.Features of the EHEIM pHcontrol+e A smart controller for monitoring and controlling the pH value in the aquarium by regulating the addition of CO2. Includes Wireless WiFi connection with a WLAN-enabled end device (smartphone, tablet, PC/MAC). Has connection and compatibility with devices of the EHEIM DIGITAL family. Measures the pH value through the pH sensor (measuring range: pH 0 to pH 14). Control range of the controller pH 6 to pH 9. Needs to be coupled via pressure reducer with CO2 bottle (EHEIM CO2 set). Electronically controls addition of CO2 through interposed magnetic valve. Adjusts CO2 addition by linking with LEDcontrol+e (day/night control) in smart mode or simple and extended bio mode with own day/night control. Queries the KH value (carbonate hardness) in advance. Sets water test and calibration reminders. Guided calibrations of the pH sensor. Sends warning for deviation of pH value (up/down). Notes if EHEIM pH sensor needs to be replaced. Provides best performance, high power, stable connection, and large memory capacity through new improved chip generation Highest safety and reliability - 3 years warranty

With the EHEIM powerRGB you will experience your aquarium like never before! Intensify the colours in your aquarium with the EHEIM powerRGB, a great addition to your aquarium lighting. To use it you need the wireless lighting control RGBcontrol+e, which will enable millions of colour nuances. This allows you - even in sync with standard lighting - to create lighting scenes depending on the time of day, such as letting clouds gather, staging dawn and dusk, simulating atmospheric moonlight with a natural cycle, and much more. There are no limits to your imagination, or configuration. Features of EHEIM powerRGB Additional light for your aquarium lighting. Ensures particularly intensive colouring of your animals and plants. Comes in 8 sizes from 36 - 135 cm (adjustable with extendable stainless steel bracket holders). Controlled by wireless lighting control EHEIM RGBcontrol+e. Extremely efficient RGB lighting with long service life (70 lm/W). Particularly safe and power efficient due to low-voltage technology. Suitable for fresh and marine water. Highest safety and reliability – comes with 3 years warranty.

With EHEIM reeflexUV+e you reduce or eliminate germ contamination and eliminate turbidity in the water. Now with WiFi controls. reeflexUV+e is the WiFi-controlled next step of the proven EHEIM UV clarifier reeflexUV. The principle of the patented reflector technology (with significantly increased germicidal UV-C radiation) has remained the same. While in conventional UV clarifiers the water flows past the UV-C burner via detours, in the EHEIM reeflexUV+e it takes a more direct route. This results in no loss of power and saves energy, being twice as efficient. The reeflexUV+e can be coupled with other products in the EHEIM Digital family and can be controlled via WLAN-enabled devices (smartphones, tablets, notebooks etc.). For example, you can select different modes, determine times and pauses and even switch to booster mode in case of a heavy parasite infestation. The reeflexUV+e should be used to support the filter in order to reduce small organisms (germs, algae spores, etc.) in the aquarium.There are 4 models for aquariums from 300 to 2000 litres. As always, this comes with EHEIM’s “Made in Germany” guarantee, ensuring the best standards in manufacturing and materials.   Advantages of the EHEIM reeflexUV+e Quickly and effectively reduces or eliminates harmful germs (bacteria, fungi, viruses, other pathogens) and infectious swarmers of fish parasites as well as suspended algae in the water Patented reflector technology: The unique arrangement of the UV-C light source and the aquarium water flowing past it, in conjunction with a special reflector, ensures unparalleled efficiency with a low energy input Almost no power loss, as the water is not deflected due to the clarifiers innovative design Excellent results: twice as effective compared to conventional UV clarifiers Also ideal for rearing tanks, as it reduces the risk of infection Bound cleaning bacteria in the filter are preserved, as only floating germs are captured Easy and safe handling and cleaning AUTO-OFF: Automatic safety shut-off when changing lamps Easy mounting due to supplied bracket Variable installation, no defined installation position or flow direction Can be coupled with other products in the EHEIM Digital family (e.g. synchronisation with the aquarium lighting) Controlled via WLAN-enabled devices (smartphone, tablet, notebook, etc.) Easy and intuitive operation Three different modes: "constant", "daily cycle", "smart coupling" Configurable burning duration, time, pauses, etc. Booster mode for combating acute parasite infestations Notification by e-mail when the lamp replacement is due Made in Germany 3 years warranty Suitable for both fresh and marine water Warning: UV-C radiation can cause damage to eyes and skin even in small doses. The light source contained in this product is intended exclusively for disinfecting aquarium water. Special technology for clear water and healthy fishIn a UV clarifier (also called UV steriliser), the aquarium water is passed in a thin film past a UV-C lamp (burner). The UV-C rays penetrate the water and kill germs, algae spores and other small organisms. With conventional technology, the water is only irradiated from one side.  EHEIM, on the other hand, has installed a reflector so that the radiation is mirrored and penetrates the water from several sides. This results in a considerably higher efficiency with reeflexUV+e. Which uses the patented EHEIM reflector technology. In addition, the EHEIM reeflexUV+e has no complicated water conduction system. The water is not diverted and flows around the burner without detours. This means that there is no loss of performance. AUTO-OFF also ensures optimum safety. Since UV-C radiation is harmful to skin and eyes, reeflexUV+e immediately and automatically switches off when the unit is opened. The EHEIM reeflexUV+e can be coupled with other products in the EHEIM Digital family (e.g. lighting). It is controlled via WLAN-enabled end devices (smartphone, tablet, notebook etc.) Operation is simple and intuitive. There are three different modes: "constant", " daily cycle" and "smart coupling". Burning duration, time, pauses, etc. can be set individually. There is a booster mode to combat acute parasite infestations. And when a lamp change is due, a message is sent by e-mail. You should also know that:Compared to natural waters, the bacterial concentration in the aquarium is relatively high due to the smaller amount of water. It is important to reduce this and bring it to a natural level. However, the aquarium water cannot and should not be completely germ-free. Only the germs floating freely in the water are captured by the UV clarifier. The bound purification bacteria in the filter (biological filtration), bacteria in the substrate etc. are spared. Turbidity of the water caused by bacteria or floating algae can be removed effectively by UV clarification. Basically, algae growth is curbed because the spores are killed. UV clarifiers generally ensure healthier fish, as the risk of infection is reduced. A UV clarifier is particularly recommended for rearing tanks. Dangerous pathogens often settle on eggs or infect young fish that do not yet have sufficient defences. UV clarification generally does not cause any change in water values. 

With EHEIM reeflexUV+e you reduce or eliminate germ contamination and eliminate turbidity in the water. Now with WiFi controls. reeflexUV+e is the WiFi-controlled next step of the proven EHEIM UV clarifier reeflexUV. The principle of the patented reflector technology (with significantly increased germicidal UV-C radiation) has remained the same. While in conventional UV clarifiers the water flows past the UV-C burner via detours, in the EHEIM reeflexUV+e it takes a more direct route. This results in no loss of power and saves energy, being twice as efficient. The reeflexUV+e can be coupled with other products in the EHEIM Digital family and can be controlled via WLAN-enabled devices (smartphones, tablets, notebooks etc.). For example, you can select different modes, determine times and pauses and even switch to booster mode in case of a heavy parasite infestation. The reeflexUV+e should be used to support the filter in order to reduce small organisms (germs, algae spores, etc.) in the aquarium.There are 4 models for aquariums from 300 to 2000 litres. As always, this comes with EHEIM’s “Made in Germany” guarantee, ensuring the best standards in manufacturing and materials.   Advantages of the EHEIM reeflexUV+e Quickly and effectively reduces or eliminates harmful germs (bacteria, fungi, viruses, other pathogens) and infectious swarmers of fish parasites as well as suspended algae in the water Patented reflector technology: The unique arrangement of the UV-C light source and the aquarium water flowing past it, in conjunction with a special reflector, ensures unparalleled efficiency with a low energy input Almost no power loss, as the water is not deflected due to the clarifiers innovative design Excellent results: twice as effective compared to conventional UV clarifiers Also ideal for rearing tanks, as it reduces the risk of infection Bound cleaning bacteria in the filter are preserved, as only floating germs are captured Easy and safe handling and cleaning AUTO-OFF: Automatic safety shut-off when changing lamps Easy mounting due to supplied bracket Variable installation, no defined installation position or flow direction Can be coupled with other products in the EHEIM Digital family (e.g. synchronisation with the aquarium lighting) Controlled via WLAN-enabled devices (smartphone, tablet, notebook, etc.) Easy and intuitive operation Three different modes: "constant", "daily cycle", "smart coupling" Configurable burning duration, time, pauses, etc. Booster mode for combating acute parasite infestations Notification by e-mail when the lamp replacement is due Made in Germany 3 years warranty Suitable for both fresh and marine water Warning: UV-C radiation can cause damage to eyes and skin even in small doses. The light source contained in this product is intended exclusively for disinfecting aquarium water. Special technology for clear water and healthy fishIn a UV clarifier (also called UV steriliser), the aquarium water is passed in a thin film past a UV-C lamp (burner). The UV-C rays penetrate the water and kill germs, algae spores and other small organisms. With conventional technology, the water is only irradiated from one side.  EHEIM, on the other hand, has installed a reflector so that the radiation is mirrored and penetrates the water from several sides. This results in a considerably higher efficiency with reeflexUV+e. Which uses the patented EHEIM reflector technology. In addition, the EHEIM reeflexUV+e has no complicated water conduction system. The water is not diverted and flows around the burner without detours. This means that there is no loss of performance. AUTO-OFF also ensures optimum safety. Since UV-C radiation is harmful to skin and eyes, reeflexUV+e immediately and automatically switches off when the unit is opened. The EHEIM reeflexUV+e can be coupled with other products in the EHEIM Digital family (e.g. lighting). It is controlled via WLAN-enabled end devices (smartphone, tablet, notebook etc.) Operation is simple and intuitive. There are three different modes: "constant", " daily cycle" and "smart coupling". Burning duration, time, pauses, etc. can be set individually. There is a booster mode to combat acute parasite infestations. And when a lamp change is due, a message is sent by e-mail. You should also know that:Compared to natural waters, the bacterial concentration in the aquarium is relatively high due to the smaller amount of water. It is important to reduce this and bring it to a natural level. However, the aquarium water cannot and should not be completely germ-free. Only the germs floating freely in the water are captured by the UV clarifier. The bound purification bacteria in the filter (biological filtration), bacteria in the substrate etc. are spared. Turbidity of the water caused by bacteria or floating algae can be removed effectively by UV clarification. Basically, algae growth is curbed because the spores are killed. UV clarifiers generally ensure healthier fish, as the risk of infection is reduced. A UV clarifier is particularly recommended for rearing tanks. Dangerous pathogens often settle on eggs or infect young fish that do not yet have sufficient defences. UV clarification generally does not cause any change in water values. 

With EHEIM reeflexUV+e you reduce or eliminate germ contamination and eliminate turbidity in the water. Now with WiFi controls. reeflexUV+e is the WiFi-controlled next step of the proven EHEIM UV clarifier reeflexUV. The principle of the patented reflector technology (with significantly increased germicidal UV-C radiation) has remained the same. While in conventional UV clarifiers the water flows past the UV-C burner via detours, in the EHEIM reeflexUV+e it takes a more direct route. This results in no loss of power and saves energy, being twice as efficient. The reeflexUV+e can be coupled with other products in the EHEIM Digital family and can be controlled via WLAN-enabled devices (smartphones, tablets, notebooks etc.). For example, you can select different modes, determine times and pauses and even switch to booster mode in case of a heavy parasite infestation. The reeflexUV+e should be used to support the filter in order to reduce small organisms (germs, algae spores, etc.) in the aquarium.There are 4 models for aquariums from 300 to 2000 litres. As always, this comes with EHEIM’s “Made in Germany” guarantee, ensuring the best standards in manufacturing and materials.   Advantages of the EHEIM reeflexUV+e Quickly and effectively reduces or eliminates harmful germs (bacteria, fungi, viruses, other pathogens) and infectious swarmers of fish parasites as well as suspended algae in the water Patented reflector technology: The unique arrangement of the UV-C light source and the aquarium water flowing past it, in conjunction with a special reflector, ensures unparalleled efficiency with a low energy input Almost no power loss, as the water is not deflected due to the clarifiers innovative design Excellent results: twice as effective compared to conventional UV clarifiers Also ideal for rearing tanks, as it reduces the risk of infection Bound cleaning bacteria in the filter are preserved, as only floating germs are captured Easy and safe handling and cleaning AUTO-OFF: Automatic safety shut-off when changing lamps Easy mounting due to supplied bracket Variable installation, no defined installation position or flow direction Can be coupled with other products in the EHEIM Digital family (e.g. synchronisation with the aquarium lighting) Controlled via WLAN-enabled devices (smartphone, tablet, notebook, etc.) Easy and intuitive operation Three different modes: "constant", "daily cycle", "smart coupling" Configurable burning duration, time, pauses, etc. Booster mode for combating acute parasite infestations Notification by e-mail when the lamp replacement is due Made in Germany 3 years warranty Suitable for both fresh and marine water Warning: UV-C radiation can cause damage to eyes and skin even in small doses. The light source contained in this product is intended exclusively for disinfecting aquarium water. Special technology for clear water and healthy fishIn a UV clarifier (also called UV steriliser), the aquarium water is passed in a thin film past a UV-C lamp (burner). The UV-C rays penetrate the water and kill germs, algae spores and other small organisms. With conventional technology, the water is only irradiated from one side.  EHEIM, on the other hand, has installed a reflector so that the radiation is mirrored and penetrates the water from several sides. This results in a considerably higher efficiency with reeflexUV+e. Which uses the patented EHEIM reflector technology. In addition, the EHEIM reeflexUV+e has no complicated water conduction system. The water is not diverted and flows around the burner without detours. This means that there is no loss of performance. AUTO-OFF also ensures optimum safety. Since UV-C radiation is harmful to skin and eyes, reeflexUV+e immediately and automatically switches off when the unit is opened. The EHEIM reeflexUV+e can be coupled with other products in the EHEIM Digital family (e.g. lighting). It is controlled via WLAN-enabled end devices (smartphone, tablet, notebook etc.) Operation is simple and intuitive. There are three different modes: "constant", " daily cycle" and "smart coupling". Burning duration, time, pauses, etc. can be set individually. There is a booster mode to combat acute parasite infestations. And when a lamp change is due, a message is sent by e-mail. You should also know that:Compared to natural waters, the bacterial concentration in the aquarium is relatively high due to the smaller amount of water. It is important to reduce this and bring it to a natural level. However, the aquarium water cannot and should not be completely germ-free. Only the germs floating freely in the water are captured by the UV clarifier. The bound purification bacteria in the filter (biological filtration), bacteria in the substrate etc. are spared. Turbidity of the water caused by bacteria or floating algae can be removed effectively by UV clarification. Basically, algae growth is curbed because the spores are killed. UV clarifiers generally ensure healthier fish, as the risk of infection is reduced. A UV clarifier is particularly recommended for rearing tanks. Dangerous pathogens often settle on eggs or infect young fish that do not yet have sufficient defences. UV clarification generally does not cause any change in water values. 

With EHEIM reeflexUV+e you reduce or eliminate germ contamination and eliminate turbidity in the water. Now with WiFi controls. reeflexUV+e is the WiFi-controlled next step of the proven EHEIM UV clarifier reeflexUV. The principle of the patented reflector technology (with significantly increased germicidal UV-C radiation) has remained the same. While in conventional UV clarifiers the water flows past the UV-C burner via detours, in the EHEIM reeflexUV+e it takes a more direct route. This results in no loss of power and saves energy, being twice as efficient. The reeflexUV+e can be coupled with other products in the EHEIM Digital family and can be controlled via WLAN-enabled devices (smartphones, tablets, notebooks etc.). For example, you can select different modes, determine times and pauses and even switch to booster mode in case of a heavy parasite infestation. The reeflexUV+e should be used to support the filter in order to reduce small organisms (germs, algae spores, etc.) in the aquarium.There are 4 models for aquariums from 300 to 2000 litres. As always, this comes with EHEIM’s “Made in Germany” guarantee, ensuring the best standards in manufacturing and materials.   Advantages of the EHEIM reeflexUV+e Quickly and effectively reduces or eliminates harmful germs (bacteria, fungi, viruses, other pathogens) and infectious swarmers of fish parasites as well as suspended algae in the water Patented reflector technology: The unique arrangement of the UV-C light source and the aquarium water flowing past it, in conjunction with a special reflector, ensures unparalleled efficiency with a low energy input Almost no power loss, as the water is not deflected due to the clarifiers innovative design Excellent results: twice as effective compared to conventional UV clarifiers Also ideal for rearing tanks, as it reduces the risk of infection Bound cleaning bacteria in the filter are preserved, as only floating germs are captured Easy and safe handling and cleaning AUTO-OFF: Automatic safety shut-off when changing lamps Easy mounting due to supplied bracket Variable installation, no defined installation position or flow direction Can be coupled with other products in the EHEIM Digital family (e.g. synchronisation with the aquarium lighting) Controlled via WLAN-enabled devices (smartphone, tablet, notebook, etc.) Easy and intuitive operation Three different modes: "constant", "daily cycle", "smart coupling" Configurable burning duration, time, pauses, etc. Booster mode for combating acute parasite infestations Notification by e-mail when the lamp replacement is due Made in Germany 3 years warranty Suitable for both fresh and marine water Warning: UV-C radiation can cause damage to eyes and skin even in small doses. The light source contained in this product is intended exclusively for disinfecting aquarium water. Special technology for clear water and healthy fishIn a UV clarifier (also called UV steriliser), the aquarium water is passed in a thin film past a UV-C lamp (burner). The UV-C rays penetrate the water and kill germs, algae spores and other small organisms. With conventional technology, the water is only irradiated from one side.  EHEIM, on the other hand, has installed a reflector so that the radiation is mirrored and penetrates the water from several sides. This results in a considerably higher efficiency with reeflexUV+e. Which uses the patented EHEIM reflector technology. In addition, the EHEIM reeflexUV+e has no complicated water conduction system. The water is not diverted and flows around the burner without detours. This means that there is no loss of performance. AUTO-OFF also ensures optimum safety. Since UV-C radiation is harmful to skin and eyes, reeflexUV+e immediately and automatically switches off when the unit is opened. The EHEIM reeflexUV+e can be coupled with other products in the EHEIM Digital family (e.g. lighting). It is controlled via WLAN-enabled end devices (smartphone, tablet, notebook etc.) Operation is simple and intuitive. There are three different modes: "constant", " daily cycle" and "smart coupling". Burning duration, time, pauses, etc. can be set individually. There is a booster mode to combat acute parasite infestations. And when a lamp change is due, a message is sent by e-mail. You should also know that:Compared to natural waters, the bacterial concentration in the aquarium is relatively high due to the smaller amount of water. It is important to reduce this and bring it to a natural level. However, the aquarium water cannot and should not be completely germ-free. Only the germs floating freely in the water are captured by the UV clarifier. The bound purification bacteria in the filter (biological filtration), bacteria in the substrate etc. are spared. Turbidity of the water caused by bacteria or floating algae can be removed effectively by UV clarification. Basically, algae growth is curbed because the spores are killed. UV clarifiers generally ensure healthier fish, as the risk of infection is reduced. A UV clarifier is particularly recommended for rearing tanks. Dangerous pathogens often settle on eggs or infect young fish that do not yet have sufficient defences. UV clarification generally does not cause any change in water values. 

With the EHEIM RGBcontrol+e you can determine the intense colours and lighting mood in your aquarium - simply from your smartphone, tablet or PC/Mac   With EHEIM RGB additional lighting, you have an enormous colour spectrum at your disposal. The colours of the fish and plants in your aquarium will gain a fascinating intensity. The colourful splendour of you underwater world will come into its own. With the RGBcontrol+e lighting control, millions of colour nuances are possible. This allows you to create lighting scenarios and moods depending on the time of day - even in sync with standard lighting - to make clouds appear, to stage dawn and dusk, to simulate atmospheric moonlight with a natural cycle, and much more. There are hardly any limits to your imagination, or individual configuration. By the way: The EHEIM incpiriaRGB cabinet lighting can also be controlled and synchronised with your aquarium lighting.   The RGBcontrol+e can be coupled with products of the EHEIM Digital family and is easily controlled via WLAN-enabled end devices (smartphone, tablet, PC/Mac).   Advantages of EHEIM RGBcontrol+e Individually configurable lighting sequence and control of the red, green and blue colour channels of the EHEIM RGB LEDs Also suitable for cabinet lighting EHEIM incpiriaRGB Ensures particularly intensive colouring of your animals and plants Sunrise and sunset, cloud effects, moonlight with natural cycle and more Selectable preset or individual scenarios Selectable “expert” mode with additional setting options Acclimatisation mode, e.g. when changing light source or setting up a new aquarium Manual updates for download from the EHEIM website, as well as automatic updates with an internet connection. Can be coupled with products of the EHEIM Digital family Wireless operation via WLAN-capable end devices (smartphone, tablet, or PC/Mac) Highest safety and reliability - 3 years warranty

With EHEIM thermocontrol+ e, we offer you the aquarium heater of the future. Intelligent and ingeniously designed.EHEIM thermocontrol+ e is our first adjustable heater with digital control via WLAN. You can set the precise temperature from 18 to 32 °C via smartphone, tablet or PC/MAC. The selected temperature is accurately measured electronically and kept constant. However, if the temperature deviates by ± 2 °C, you will be notified immediately by e-mail. Automatic synchronisation with filter activity or lighting is also possible, this means you can wirelessly connect to the EHEIM professionel 5e Filter or to the LEDcontrol+.The construction of the thermocontrol +e conforms to that of our proven thermocontrol heaters. The combination of the special laboratory glass cover, the flawless finish, the high quality materials and the absolute reliability, provides the ultimate heater. The heaters have a 3-year guarantee and there are 4 sizes to choose from - whether you want to heat a 200 or 1000 litre aquarium.Advantages of EHEIM thermocontrol+ e Electronic aquarium heater with integrated WLAN function and digital control via smartphone, tablet or PC/MAC. Precise temperature setting from 18 to 32 °C Control accuracy ± 0,5 °C Indicator lights show heating function and operating status Notification to stored e-mail address as soon as the temperature deviates by ± 2 °C Smart linking with other electronically controlled devices of the EHEIM.digital family Synchronisation: temperature water flow adjustment or for lowering the set temperature at night, etc.) If necessary, adjustment with external thermometer (expert mode) Waterproof (IPX8) - for optimum wifi signal reception, immerse the heater in water up to the mark Dry-run protection (Thermo Safety Control) Convenient cable length of approx. 170 cm Double suction holder included 4 sizes for aquariums from 200 up to 1000 litres Suitable for both fresh and marine water Highest safety and reliability with a 3 year guarantee. The smart aquarium heater with integrated WLAN function and digital control via smartphone, tablet or PC/MAC. Adjustment and controlThe EHEIM thermocontrol+ e aquarium heater is the advanced development of the thermocontrol e heater. Unlike the latter, it is not set manually, but programmed and monitored wirelessly via WLAN and by smartphone, tablet or PC/MAC. It can be accurately set from 18 to 32 °C. If the set temperature ever deviates by +/-2 degrees, you will receive an e-mail notification, provided you have stored a corresponding address. Synchronisation with other devicesA special highlight is that the thermocontrol+ e can be synchronised with other devices in the Eheim Digital Family such as the EHEIM professionel 5e filter or the lighting control LEDcontrol+. You can therefore specify that the set temperature rises or falls when, for example, the filter flow (in bio mode) increases or decreases or the LED lighting is switched off or on. Example: The filter flow is increased at night and the lighting is switched off. The set temperature is automatically adjusted accordingly: 25 °C during the day; 23 °C at night. (Please note: Water is not cooled down - the heater has no integrated cooling).WLAN-connectionThe thermocontrol+ e is waterproof and fully submersible. For an optimal WLAN connection, however, the heater may only be immersed up to the "water level" mark.For the security of your device, every EHEIM thermocontrol+ e is encrypted ex works (password can be adjusted). After setting the desired temperature, the wifi network can be switched off.

With EHEIM thermocontrol+ e, we offer you the aquarium heater of the future. Intelligent and ingeniously designed.EHEIM thermocontrol+ e is our first adjustable heater with digital control via WLAN. You can set the precise temperature from 18 to 32 °C via smartphone, tablet or PC/MAC. The selected temperature is accurately measured electronically and kept constant. However, if the temperature deviates by ± 2 °C, you will be notified immediately by e-mail. Automatic synchronisation with filter activity or lighting is also possible, this means you can wirelessly connect to the EHEIM professionel 5e Filter or to the LEDcontrol+.The construction of the thermocontrol+ e conforms to that of our proven thermocontrol heaters. The combination of the special laboratory glass cover, the flawless finish, the high quality materials and the absolute reliability, provides the ultimate heater. The heaters have a 3-year guarantee and there are 4 sizes to choose from - whether you want to heat a 200 or 1000 litre aquarium.Advantages of EHEIM thermocontrol+ e Electronic aquarium heater with integrated WLAN function and digital control via smartphone, tablet or PC/MAC. Precise temperature setting from 18 to 32 °C Control accuracy ± 0,5 °C Indicator lights show heating function and operating status Notification to stored e-mail address as soon as the temperature deviates by ± 2 °C Smart linking with other electronically controlled devices of the EHEIM.digital family Synchronisation: temperature water flow adjustment or for lowering the set temperature at night, etc.) If necessary, adjustment with external thermometer (expert mode) Waterproof (IPX8) - for optimum wifi signal reception, immerse the heater in water up to the mark Dry-run protection (Thermo Safety Control) Convenient cable length of approx. 170 cm Double suction holder included 4 sizes for aquariums from 200 up to 1000 litres Suitable for both fresh and marine water Highest safety and reliability with a 3 year guarantee. The smart aquarium heater with integrated WLAN function and digital control via smartphone, tablet or PC/MAC. Adjustment and controlThe EHEIM thermocontrol+ e aquarium heater is the advanced development of the thermocontrol e heater. Unlike the latter, it is not set manually, but programmed and monitored wirelessly via WLAN and by smartphone, tablet or PC/MAC. It can be accurately set from 18 to 32 °C. If the set temperature ever deviates by +/-2 degrees, you will receive an e-mail notification, provided you have stored a corresponding address. Synchronisation with other devicesA special highlight is that the thermocontrol+ e can be synchronised with other devices in the Eheim Digital Family such as the EHEIM professionel 5e filter or the lighting control LEDcontrol+. You can therefore specify that the set temperature rises or falls when, for example, the filter flow (in bio mode) increases or decreases or the LED lighting is switched off or on. Example: The filter flow is increased at night and the lighting is switched off. The set temperature is automatically adjusted accordingly: 25 °C during the day; 23 °C at night. (Please note: Water is not cooled down - the heater has no integrated cooling).WLAN-connectionThe thermocontrol+ e is waterproof and fully submersible. For an optimal WLAN connection, however, the heater may only be immersed up to the "water level" mark.For the security of your device, every EHEIM thermocontrol+ e is encrypted ex works (password can be adjusted). After setting the desired temperature, the wifi network can be switched off.

With EHEIM thermocontrol+ e, we offer you the aquarium heater of the future. Intelligent and ingeniously designed.EHEIM thermocontrol+ e is our first adjustable heater with digital control via WLAN. You can set the precise temperature from 18 to 32 °C via smartphone, tablet or PC/MAC. The selected temperature is accurately measured electronically and kept constant. However, if the temperature deviates by ± 2 °C, you will be notified immediately by e-mail. Automatic synchronisation with filter activity or lighting is also possible, this means you can wirelessly connect to the EHEIM professionel 5e Filter or to the LEDcontrol+.The construction of the thermocontrol+ e conforms to that of our proven thermocontrol heaters. The combination of the special laboratory glass cover, the flawless finish, the high quality materials and the absolute reliability, provides the ultimate heater. The heaters have a 3-year guarantee and there are 4 sizes to choose from - whether you want to heat a 200 or 1000 litre aquarium.Advantages of EHEIM thermocontrol+ e Electronic aquarium heater with integrated WLAN function and digital control via smartphone, tablet or PC/MAC. Precise temperature setting from 18 to 32 °C Control accuracy ± 0,5 °C Indicator lights show heating function and operating status Notification to stored e-mail address as soon as the temperature deviates by ± 2 °C Smart linking with other electronically controlled devices of the EHEIM.digital family Synchronisation: temperature water flow adjustment or for lowering the set temperature at night, etc.) If necessary, adjustment with external thermometer (expert mode) Waterproof (IPX8) - for optimum wifi signal reception, immerse the heater in water up to the mark Dry-run protection (Thermo Safety Control) Convenient cable length of approx. 170 cm Double suction holder included 4 sizes for aquariums from 200 up to 1000 litres Suitable for both fresh and marine water Highest safety and reliability with a 3 year guarantee. The smart aquarium heater with integrated WLAN function and digital control via smartphone, tablet or PC/MAC. Adjustment and controlThe EHEIM thermocontrol+ e aquarium heater is the advanced development of the thermocontrol e heater. Unlike the latter, it is not set manually, but programmed and monitored wirelessly via WLAN and by smartphone, tablet or PC/MAC. It can be accurately set from 18 to 32 °C. If the set temperature ever deviates by +/-2 degrees, you will receive an e-mail notification, provided you have stored a corresponding address. Synchronisation with other devicesA special highlight is that the thermocontrol+ e can be synchronised with other devices in the Eheim Digital Family such as the EHEIM professionel 5e filter or the lighting control LEDcontrol+. You can therefore specify that the set temperature rises or falls when, for example, the filter flow (in bio mode) increases or decreases or the LED lighting is switched off or on. Example: The filter flow is increased at night and the lighting is switched off. The set temperature is automatically adjusted accordingly: 25 °C during the day; 23 °C at night. (Please note: Water is not cooled down - the heater has no integrated cooling).WLAN-connectionThe thermocontrol+ e is waterproof and fully submersible. For an optimal WLAN connection, however, the heater may only be immersed up to the "water level" mark.For the security of your device, every EHEIM thermocontrol+ e is encrypted ex works (password can be adjusted). After setting the desired temperature, the wifi network can be switched off.

With EHEIM thermocontrol+ e, we offer you the aquarium heater of the future. Intelligent and ingeniously designed.EHEIM thermocontrol+ e is our first adjustable heater with digital control via WLAN. You can set the precise temperature from 18 to 32 °C via smartphone, tablet or PC/MAC. The selected temperature is accurately measured electronically and kept constant. However, if the temperature deviates by ± 2 °C, you will be notified immediately by e-mail. Automatic synchronisation with filter activity or lighting is also possible, this means you can wirelessly connect to the EHEIM professionel 5e Filter or to the LEDcontrol+.The construction of the thermocontrol+ e conforms to that of our proven thermocontrol heaters. The combination of the special laboratory glass cover, the flawless finish, the high quality materials and the absolute reliability, provides the ultimate heater. The heaters have a 3-year guarantee and there are 4 sizes to choose from - whether you want to heat a 200 or 1000 litre aquarium.Advantages of EHEIM thermocontrol+ e Electronic aquarium heater with integrated WLAN function and digital control via smartphone, tablet or PC/MAC. Precise temperature setting from 18 to 32 °C Control accuracy ± 0,5 °C Indicator lights show heating function and operating status Notification to stored e-mail address as soon as the temperature deviates by ± 2 °C Smart linking with other electronically controlled devices of the EHEIM.digital family Synchronisation: temperature water flow adjustment or for lowering the set temperature at night, etc.) If necessary, adjustment with external thermometer (expert mode) Waterproof (IPX8) - for optimum wifi signal reception, immerse the heater in water up to the mark Dry-run protection (Thermo Safety Control) Convenient cable length of approx. 170 cm Double suction holder included 4 sizes for aquariums from 200 up to 1000 litres Suitable for both fresh and marine water Highest safety and reliability with a 3 year guarantee. The smart aquarium heater with integrated WLAN function and digital control via smartphone, tablet or PC/MAC. Adjustment and controlThe EHEIM thermocontrol+ e aquarium heater is the advanced development of the thermocontrol e heater. Unlike the latter, it is not set manually, but programmed and monitored wirelessly via WLAN and by smartphone, tablet or PC/MAC. It can be accurately set from 18 to 32 °C. If the set temperature ever deviates by +/-2 degrees, you will receive an e-mail notification, provided you have stored a corresponding address. Synchronisation with other devicesA special highlight is that the thermocontrol+ e can be synchronised with other devices in the Eheim Digital Family such as the EHEIM professionel 5e filter or the lighting control LEDcontrol+. You can therefore specify that the set temperature rises or falls when, for example, the filter flow (in bio mode) increases or decreases or the LED lighting is switched off or on. Example: The filter flow is increased at night and the lighting is switched off. The set temperature is automatically adjusted accordingly: 25 °C during the day; 23 °C at night. (Please note: Water is not cooled down - the heater has no integrated cooling).WLAN-connectionThe thermocontrol+ e is waterproof and fully submersible. For an optimal WLAN connection, however, the heater may only be immersed up to the "water level" mark.For the security of your device, every EHEIM thermocontrol+ e is encrypted ex works (password can be adjusted). After setting the desired temperature, the wifi network can be switched off.